Drivers / setters / hand tools

Site tools and accessories that fit the fastener.

Buy against the head and interface, not a bigger case. The Jorkli building components catalogue pairs practical hand tools with the fixings they serve. Store buyers and site crews can request driver sets or individual accessories through Austin, Texas.

Send an enquiry

Enquiry basis: per set or piece

Driver sets are considered per set. Wrenches per piece. Magnetic nut setters per piece or set. Set contents, working size and quantity determine the basis; amounts in USD require confirmation after enquiry.

No live stock count or automatic delivery date. This is component supply, not a power-tool hire or repair service.

Drive profileAcross flatsShank interfaceWorking clearanceReplacement size

The fit record

A tool that nearly fits damages the part.

The useful difference is at the contact point. These listings separate the bit recess, the nut flats and the tool-side interface before discussing a set.

A loose driver can round the recess and leave a screw half seated. An oversized setter can turn a small hex head into a removal job. Record the fastener dimensions from its specification rather than estimating them from the size of the wrench handle.

01
Fastener-side fit
Drive profile and size for a bit; actual across-flats size for a wrench or setter. Screw diameter and hex-head size are different measurements.
02
Tool-side fit
A hand driver, a bit holder and a powered tool may share an interface without sharing an impact-use rating. State the tool and the intended mode.
03
Reach and obstruction
The bit or socket body must reach the head without fouling a washer, sheet profile or adjacent bracket. More length can mean less control.
04
What the set contains
Compare usable sizes and replacement needs. A set count by itself does not tell you whether it includes the interface your fastener requires.

Practical site lines

Replace the missing working size, or build a useful set.

These are tools for the catalogue's fastening work. Specify a repeat requirement if you are replenishing a trade counter, or name the fastener and access problem if the request comes from a live assembly. The enquiry can cover tools and components together.

Worker using a hand driver set on a timber frame — Drive engagement comes before turning force. Match the bit to the recess and seat it fully.

01 / Hand driver sets

A compact set for the heads on the job

A hand driver set combines a handle or holder with working bits for fastener recesses. It suits fit-up and replacement work where access and controlled hand pressure matter. For Torx construction screws, ask for the actual drive size. A general assortment is not proof that the bit you need is inside.

The bit material, handle construction and included sizes are checked against the proposed set. No alloy grade or insulated-tool rating is stated for an unspecified line. If your work requires electrical protection, a calibrated torque setting or impact-rated bits, say so before comparing sets.

Fastener interface: Recess profile and exact bit size to be identified
Tool construction: Hand driver with compatible replaceable bits; set contents to be confirmed
Working reach: Bit and holder length suited to the access around the fixing
Enquiry basis: Per set, with included sizes and quantity confirmed

Do not carry a worn fit forward.If a bit rocks in an undamaged recess, check its size and condition. Extra pressure does not restore missing engagement.

Torx wood-screw specifications

Adjustable wrench turning a nut on a site assembly — A close jaw fit bears on the flats. A loose setting concentrates force at the corners.

02 / Adjustable wrench

Jaw range that reaches the actual nut

An adjustable wrench is a general fastening tool with a movable jaw. It suits maintenance buyers dealing with different nut sizes, provided the jaw range and head clearance fit the assembly. The overall tool length tells only part of that story. Ask about the maximum opening and available swing around the nut.

Construction material, finish and jaw geometry depend on the confirmed product. This catalogue does not attach a material grade or precision tolerance to an unidentified wrench. Where a connection specifies a tightening torque, use the specified torque-control method rather than treating this tool as a measuring device.

Working interface: Nut or bolt-head flats within the confirmed jaw range
Access detail: Head thickness, surrounding obstruction and available handle swing
Selection context: General hand fastening and holding a compatible opposing nut
Enquiry basis: Per piece; tool size and jaw range confirmed on enquiry

Matching nuts and washers

03 / Magnetic nut setters

Hold the hex head without confusing retention with fit.

Magnetic retention helps position a compatible fastener. It does not compensate for a socket that is the wrong size.

Magnetic nut setters are driver accessories for compatible external-hex fasteners. The socket engages the head while the shank engages the tool or holder. State both dimensions. For roofing screws, include washer clearance and the sheet profile, because the outside of the setter can foul the assembly before the fastener is seated.

The working socket material and tool-use rating must be confirmed for the chosen accessory. Magnetic retention also depends on the fastener material. Do not assume that a stainless fastener responds to a magnet in the same way as another steel fixing. The head still needs full mechanical engagement.

Fastener-side dimension: Hex size across flats, not thread diameter
Tool-side dimension: Shank interface and retention arrangement
Use condition: Powered or hand use; impact suitability requires an explicit product rating
Enquiry basis: Per piece or set; working sizes and quantity confirmed

Debris changes the seating depth.Collected metal particles can keep a head from seating fully in a magnetic setter. Check and clean the accessory using its manufacturer's instructions before diagnosing the screw as the wrong size.

Send an enquiry Sheet-fixing requirements

Buying comparison

Ask for the dimension that does the work.

Carry the units into the enquiry. Near-matching metric and inch dimensions are not interchangeable just because a tool starts to engage.

Information to compare before requesting a price basis
Tool line	First measurement	Second check	Buying unit
Hand driver set	Recess profile and bit designation from the screw specification	Holder connection, bit reach and required sizes in the set	Set, contents confirmed
Adjustable wrench	Across-flats size of the nut or head	Jaw opening and room for the wrench head and handle	Piece, working range confirmed
Magnetic nut setter	External hex dimension with the unit stated	Shank interface, socket depth and powered-tool rating	Piece or set, sizes confirmed

No size range is offered as available until the line is checked. This record describes what to specify; it does not imply an in-stock assortment.

Enquiry sequence

Start with the fastener. Finish with the right buying unit.

For a store restock, list the sizes that actually turn over. For a site requirement, describe the part that needs turning. The same enquiry route accepts either request without asking you to build a retail cart.

Name the working interface.Include the fastener reference or drive size. If you are replacing a setter, state the socket and shank dimensions separately, with units.
Describe access and the tool in use.Note a recessed head, a projecting washer or a nearby bracket. Identify whether the accessory is for a hand driver or a powered tool and whether impact use is required.
Separate pieces from sets.State the quantity of each working size or the set contents you need. An assortment request is checked as an assortment, not assumed to contain every head profile.
Review the confirmed line.After enquiry, Jorkli checks compatibility, availability, pack contents and lead time. Any quotation needs its supply basis and applicable charges made clear before you decide to proceed. A request alone is not an order.

Before you choose

A general hand tool is not a specialist rating.

We do not describe these lines as electrically insulated, calibrated or suitable for impact work without the selected product's stated rating. If the project demands one of those properties, put that requirement in the request. The catalogue is not a substitute for a required tool certificate or a project method.

Need only one replacement size? Enquire for that size. Piece availability is checked rather than promised, and a per-set basis may still apply to the offered line. Need an entire power-tool system or tool repair? Those are outside this catalogue's stated scope.

There is no generic warranty term attached to a picture of a tool. Product-specific manufacturer terms need confirmation in writing before an order; the warranty information explains that boundary.

Site tool enquiries

Ask for a tool that fits, not a bigger assortment.

Give the working size and the fastener it serves. Add the quantity and whether you need replacement pieces or complete sets.

The contact form accepts tool and component requirements together. Include a phone number or email so Jorkli can resolve the missing fit details before confirming a supply basis.

Send an enquiry

Piece or set / Contents checked on enquiry / No online payment

Site tools and accessories that fit the fastener.

A tool that nearly fits damages the part.

Fastener-side fit

Tool-side fit

Reach and obstruction

What the set contains

A compact set for the heads on the job

Jaw range that reaches the actual nut

Start with the fastener. Finish with the right buying unit.

A general hand tool is not a specialist rating.

Tools are only one side of the fit.

Ask for a tool that fits, not a bigger assortment.

Component support